This paper gives an overview of industrial SMB chromatography and focusses on the strategy how to develop a purification system either in the early development phase of a product or to assess whether a batch process can be optimised and scaled into a continuous process.
Biotechnological fermentation processes are widely used in industry to produce an abundant range of organic products which often need to be purified in order to meet high-quality standards.
Typical bioprocesses comprise:
Industrial Bioprocesses can be
Reducing downstream process steps can reduce capital investment and operational costs and reduce the overall energy consumption of an industrial process.
Conventional downstream processing involves biomass separation from the soluble fractions of the fermentation broth as a first step (e.g. filtration, centrifugation). Hereafter, other downstream process steps follow, depending on the required product purity and concentration. Decolorization is often necessary to remove the brownish
A typical process flow diagram is shown in the figure below.
Conventional bioprocesses can be summarised by the following steps:
In adsorption processes, the adsorbent is held in a (pressure) vessel, most often called a resin vessel. The stationary phase is referred to as a packed resin bed. As the process fluid flows through the vessel, the resin attains an equilibrium with the process fluid, resulting in a mass transfer zone that gradually moves through the bed. If the mass transfer zone has reached the exit of the resin bed, the bed is saturated and “breaks through”. The resin needs to be washed and regenerated before it can be loaded again. As a consequence, continuous processing of the liquid requires at least two fixed beds, but usually, three beds are installed.
In the previous century, the advantages of continuous countercurrent processing have been
In SMB technology, the chromatography material is kept inside columns or vessels. The transport of the chromatography material is obtained by periodically switching in- and outlet positions.
In the 1980’s, the SMB concept was originally developed for binary fractionation processes, where a stronger and weaker binding component
A state of the art example of such fractionating system is the production of High Fructose syrup fractions in the sugar industry. Here the Fructose is the monosaccharide with a stronger affinity towards the resin compared to Glucose.
At a somewhat later stage, the same concept has also been developed for bind and elute systems. Bind and elute systems typically comprise –at least- the following zones:
This zone distribution is not restricted to the four as mentioned, for instance, regeneration and cleaning in place have been frequently applied.
Bind and elute SMB systems are designed in carrousel configuration, featuring a central rotating fluid distribution valve, and a static vessel configuration featuring a valve block for each individual resin vessel. Each valve block is identical and comprises a number of valves accommodating all in- and outlet flows that have been defined for the chromatographic cycle.
The below figure represents a typical conceptual flow diagram for a bind and
Bind and elute IX chromatography systems based on the SMB principle has opened a huge field of applications where valuable products are recovered or purified on a continuous basis thereby saving substantial water consumption as well as elute and
Xendo has the experience and capability to design and build custom-made SMB continuous Ion Exchange and Chromatography systems under the product name XPure™.
In general, a process development study can be approached from different angles and started or
When developing a production process first the target objectives should be defined; what is the required yield and purity of the target compound; what is the composition of the starting material (feed); which recovery or purification process is most beneficial in terms of energy (including clean water) and material consumption and gives the least waste production; what is the scale of continuous operation.
If industrial (IX) chromatography could be
If literature cannot elucidate the case, based on the molecular structural or other adsorption relevant
Depending on the specific adsorption capacity of the target molecule onto the resin, further column tests – so-called breakthrough tests- will produce data on the resin capacity and information on how to elute (buffer composition, treatment ratio) the target molecule.
In the case, that potential resin candidates can be identified for the purification job the column tests can be elaborated with further break-through or pulse-tests at variable process conditions that cover the window of operation in a full-scale industrial setting. Typically this is conducted on one or two best performing resin candidates from the previous stage.
Here a Design of Experiment approach combined with the rationale of experienced chromatography engineering practice is used to define how many column tests will be conducted and what parameters will be varied at different levels.
Based on the data from the extended tests a preliminary process design and CAPEX/OPEX estimate can be made. Here we have developed our design tool where all relevant parameters can be put in and the outcome shows a full-scale SMB configuration and equipment dimensions. Dimensional data refer to a number of individual resin cells, dimensions of resin cells, line and valve sizing and pressure drop per distinct zone.
The design tool is based on the 2-film mass transfer kinetics model which is the principle for which we have created an algorithm. The design tool further features the (universal) Kremser equation for counter-current contacting.
A set of physical and mass flow-related variables have been accounted for. The most important parameters are:
Resin porosity, particle size (specific area) and evidently the most important -- specific adsorption capacity; diffusivity in both liquid and stationary phase; void fraction of resin bed; bed velocity; fluid viscosity and temperature.
The design tool could also be deployed if the adsorption system is a state of the art process, or close to this. In that case lab scale column tests could be skipped, and the specific feed characteristics need to be combined with the (specific) resin type that could do the purification/recovery job.
The output of the design tool can be used to do preliminary cost and value engineering. The outcome is essential to evaluate the purification/recovery process.
In the case of a positive decision, i.e.
Here we can enter two different scales for piloting.A
2. A large pilot SMB system featuring a bit larger resin cells from 1-4 inch column diameter on average 400-1000 mm bed height.
The selection merely depends on the availability of adequate feed and buffer volumes, any uncertainties that may not adequately be identified on an industrial scale, for example, impurities presence and identification, the presence of suspended solids or temperature variations.
The outcome of a pilot study will be a robust design of the industrial scale process also featuring chemical consumption figures, product
Simulated Moving Bed has distinct benefits over classical single column systems with significantly higher
This continuous production system is increasingly used on
If you’d like to investigate what SMB could mean for your production processes don’t hesitate to contact us or have a look at our currently available systems: XPure-C & XPure-S. We also have a wide variety of pilot studies available for those interested.